Skip to content
← Glossary

Vignetting

Vignetting is the darkening of an image's corners relative to the center. It can be an optical flaw or a creative effect added in editing.

Also known as: corner shading, light falloff

Vignetting is the darkening of an image's corners relative to the center. It can be an optical flaw (the lens design, a very wide aperture, stacked filters on a wide angle) or an effect added on purpose in editing to draw the eye to the center of the frame. On a fast lens, the falloff at maximum aperture usually runs between one and two stops at the corner, and almost disappears two stops further stopped down.

A frame with concentric zones showing the light falloff from the center to the corners, and a curve comparing that falloff at maximum aperture and with the aperture stopped down two stops

The falloff is gradual and radial. A hard black edge is not optical vignetting: it is something blocking the frame.

Where does the vignetting in my photo come from?

Before correcting it, it helps to know which of the four you are looking at, because they are not fixed the same way.

  • Type: Natural; Cause: Light falls off with the cosine to the fourth power of the angle; How it looks: Soft, symmetrical gradient; What fixes it: Lens profile in the raw converter

  • Type: Optical; Cause: The lens barrel itself blocks oblique rays; How it looks: Soft, worse at maximum aperture; What fixes it: Stopping down two stops, or the profile

  • Type: Mechanical; Cause: Stacked filters, the wrong lens hood, an adapter; How it looks: Black corners with a defined edge; What fixes it: Removing the filter or using a thin-mount one

  • Type: Creative; Cause: Added in editing; How it looks: Whatever you decide; What fixes it: A brush: it is intentional

The mechanical kind is the only one that cannot be corrected afterward: where no light arrived there is no information to recover. It appears mainly below 20 mm on full frame, which is where the angle of view grazes the mount of any filter.

When should I remove it and when should I leave it?

Remove it completely when uniformity matters: product on a white background, artwork reproduction, document copying, astrophotography and, above all, panoramas. In a panorama the vignetting of each shot becomes vertical bands when the images are stitched, so the correction goes before assembly, never after. It is covered in the guide to panoramas and architectural photography.

Leave it or reinforce it when the subject is centered and the background competes: portrait, reportage, street. A well-placed creative vignette is noticeable in the path of the gaze and not in the image.

How do I apply a creative vignette that does not stand out?

With an inverted radial mask, not with the global slider, because the subject is almost never at the geometric center. Place the ellipse over the face, invert the selection and lower the exposure between −0.3 and −0.6 EV, with a wide feather, 60 to 80%.

Check two things before calling it done: that no corner falls below true black (look at it in the histogram) and that the effect is still subtle on a screen brighter than yours.

Common mistakes

  • Applying the lens profile and on top of it a creative vignette without looking. They add up and the corners close in twice as much as you intended.

  • Stacking a polarizer and ND on a 16 mm. See polarizing filter: with two mounts in front, the corners get cut off and no editing fixes it.

  • Correcting vignetting after cropping. The profile assumes the full frame; on an image already cropped permanently, the correction does not match the optical center.

  • Using it to hide a messy background. Darkening a corner does not eliminate what is in it. Change the angle when shooting.

  • Confusing it with a color tint in the corners. That is something else; if you see color halos on high-contrast edges, see chromatic aberration.

The optical behavior depends on the lens design, the topic of the guide to lens selection and creative use. To see it as both a correction and a creative device, see landscape editing: complete Lightroom workflow.

  • Blog
    Advanced Autofocus: Nail the Eye in Every Photo

    Advanced autofocus step by step: AF modes, back-button focus and what to use in each scenario for perfectly sharp portraits and action.

  • Glossary
    Reproduction ratio (1:1 macro)

    Reproduction ratio, or magnification, is the size a subject is projected onto the sensor compared with its real size.

  • Guide
    Autofocus Systems

    Modern autofocus systems offer multiple zones, predictive tracking and subject detection: choose the right mode for each situation.

  • Blog
    Hyperfocal Distance in Practice: Sharp Landscapes

    Hyperfocal distance explained without formulas: how to focus landscapes so everything comes out sharp, with practical values by focal length and aperture.

  • Glossary
    Zone focusing

    Zone focusing is a manual focus technique: prefocus the lens at a fixed distance and stop down so depth of field keeps subjects sharp without refocusing.

  • Guide
    Depth of Field in Practice

    Depth of field directs the viewer's attention and creates visual hierarchy: your most powerful storytelling tool.

  • Guide
    Autofocus Systems

    Modern autofocus systems offer multiple zones, predictive tracking and subject detection: choose the right mode for each situation.

  • Guide
    Depth of Field in Practice

    Depth of field directs the viewer's attention and creates visual hierarchy: your most powerful storytelling tool.