Image stabilization (IS/VR/OSS)
Image stabilization compensates for camera shake during exposure, letting you shoot handheld at slower shutter speeds than would otherwise be possible.
Also known as: IBIS, optical stabilization, vibration reduction, IS
Image stabilization is a system that compensates for camera shake during exposure and lets you shoot handheld at slower speeds than would be possible without it. Depending on the brand it is called IS, VR or OSS when it lives in the lens, and IBIS when it is the sensor that moves. With 3 stops of gain, a 100 mm on full frame goes from needing 1/100 s to holding at 1/13 s.
Stabilization moves the limit for your own shake. The subject's motion stays exactly where it was.
What shutter speed can I use with stabilization?
The starting point is the reciprocal rule: the minimum handheld speed is 1 divided by the full-frame equivalent focal length. Each stop of stabilization doubles that time.
Equivalent focal length: 24 mm; Unstabilized: 1/25 s; With 3 stops: 1/3 s; With 5 stops: 1.3 s
Equivalent focal length: 35 mm; Unstabilized: 1/40 s; With 3 stops: 1/5 s; With 5 stops: 0.8 s
Equivalent focal length: 50 mm; Unstabilized: 1/50 s; With 3 stops: 1/6 s; With 5 stops: 0.6 s
Equivalent focal length: 100 mm; Unstabilized: 1/100 s; With 3 stops: 1/13 s; With 5 stops: 1/3 s
Equivalent focal length: 200 mm; Unstabilized: 1/200 s; With 3 stops: 1/25 s; With 5 stops: 1/6 s
Equivalent focal length: 400 mm; Unstabilized: 1/400 s; With 3 stops: 1/50 s; With 5 stops: 1/13 s
The spec-sheet numbers are measured in a lab, on a test bench and at a specific focal length. In the cold, after walking for an hour, or with your body twisted over a railing, expect less margin than advertised. Fire a short burst of three shots and keep the sharp one: at those speeds, the hit rate matters more than the record.
When should I turn it off?
On a tripod, with exposures longer than a second. The system looks for a movement that doesn't exist and can introduce its own drift. Many bodies detect this, but not all, and checking costs one shot.
When panning. If your equipment has mode 2 or a panning mode, use it: it stabilizes only the vertical axis and lets the horizontal movement through. See panning.
At very high speeds. Above 1/1000 s it adds nothing and drains the battery.
In astrophotography on a tripod. There the limit is set by the 500 rule, not your hands.
Does it replace the tripod?
No, and for two different reasons. The first is the subject: a person walking needs 1/125 s and a child running 1/500 s, whatever stabilization the camera has. The second is framing: below half a second the tripod fixes the framing, and only with the framing fixed can you stack shots or repeat the same composition an hour later.
Where it does replace it is in the middle ground. A museum interior at 1/13 s with a 35 mm, a landscape at dusk at 1/4 s resting your elbow on a rock, a night street at 1/8 s: there a stabilized body solves shots that used to require carrying three kilos.
Common mistakes
Blaming stabilization for a photo blurred by the subject. Check the file at 100%: if the background is sharp and the person isn't, the problem was shutter speed.
Firing it cold. The system needs a moment to settle. Hold the shutter button halfway for a second before shooting.
Trusting a single shot at 5 stops. At those speeds the result is statistical. Take three shots and pick.
Combining body and lens stabilization without checking. Some systems cooperate and others get in each other's way; the real combination depends on your gear.
Lowering the shutter speed instead of raising the ISO when there is movement. See ISO and decide what noise you accept before accepting blur.
For handheld sharpness techniques, see the guide to advanced equipment and maintenance, the one on shutter speeds and the article urban night photography without a tripod: ISO and stabilization.