ISO
ISO measures how sensitive the camera's sensor is to light.
Also known as: ISO sensitivity, film speed, sensor gain
ISO measures the camera sensor's sensitivity to light. Low values (ISO 100) demand more ambient light but give clean images; high values (ISO 3200, 6400) let you shoot in dim light at the cost of digital noise and loss of fine detail. Each doubling of ISO equals one stop of light: in the same scene at f/2.8, going from ISO 800 to ISO 1600 raises the shutter speed from 1/30 s to 1/60 s.
Raising ISO doesn't add light: it spreads the same light with more gain. What you gain in speed you pay for in noise.
What ISO do I use in each scene?
These values are calculated for full frame and are consistent with each other: they start from sunny 16 and move in full stops.
Scene: Full sun, midday; ISO: 100; Aperture: f/16; Shutter speed: 1/100 s; Note: Sunny 16; equivalent to f/8 and 1/400 s
Scene: Bright overcast; ISO: 100; Aperture: f/8; Shutter speed: 1/100 s; Note: Two stops less light than in full sun
Scene: Outdoor shade; ISO: 200; Aperture: f/5.6; Shutter speed: 1/200 s; Note: Three stops below direct sun
Scene: Daytime interior by a window; ISO: 400; Aperture: f/2.8; Shutter speed: 1/125 s; Note: Portrait with natural light
Scene: Night interior with lamps; ISO: 1600; Aperture: f/2.8; Shutter speed: 1/60 s; Note: Still subject; if they walk, go up to 3200
Scene: Sports in an indoor arena; ISO: 6400; Aperture: f/2.8; Shutter speed: 1/500 s; Note: Shutter speed rules: ISO adapts
Scene: Milky Way under a dark sky; ISO: 3200; Aperture: f/2.8; Shutter speed: 20 s; Note: On a tripod and with the 500 rule
On APS-C, with the same aperture and shutter speed, each pixel collects less signal: for night shots you usually need one more stop of ISO than in the table. To compare formats, use the crop factor converter.
Is it better to raise ISO or lift the photo afterward?
Raise ISO at capture, almost always. A photo exposed at ISO 6400 and another shot at ISO 800 and lifted three stops in processing receive the same light, but the second carries more shadow noise and worse color, because the gain was applied after the signal was digitized.
The exception is the moments when you need to protect specific highlights —a stage, a candle, a background flash— and you prefer to recover shadows rather than blow out the bright spot. Check where the highlights fall on the histogram before deciding.
How do I set up auto ISO?
Three settings and you can forget the dial for the whole outing:
Range: from 100 to a ceiling you have tested on your own gear. Shoot the same scene at 3200, 6400 and 12800, look at the files at 100% and choose where you stop liking it.
Minimum shutter speed: 1 divided by the equivalent focal length if the subject is still, and double that if it moves. With a 50 mm and people walking, 1/125 s.
Exposure compensation: keeps working with auto ISO, in M mode too on most bodies.
Common mistakes
Leaving ISO 6400 on from the day before. Checking the ISO when you turn on the camera takes a second and saves the first hour of light.
Lowering the shutter speed instead of raising ISO. A noisy photo gets published; a blurry one doesn't.
Using the extended L and H values. They aren't real sensor gain: they are a digital push you could also give in processing, with less control.
Applying noise reduction at maximum. Past halfway on the control, skin and foliage textures turn to plastic. Work on sharpening too to compensate.
Comparing ISO across formats as if it were the same thing. ISO 3200 on a small sensor doesn't collect the same signal as on full frame.
ISO is the third pillar of the exposure triangle, alongside aperture and shutter speed. For practical limits and exercises, see the guide to smart ISO and the article how high should you push ISO? Limits by camera.