Color temperature (Kelvin)
Color temperature describes whether a light source leans orange or blue, measured in Kelvin (K). Low values are warm light and high values are cool light.
Also known as: Kelvin, white point
Color temperature describes whether a light source leans orange or blue. A candle sits around 1,900 degrees; an incandescent bulb, between 2,700 and 3,000; clear midday, 5,500; shade under a clear sky goes past 7,000. That scale is measured in degrees Kelvin (K) and works the opposite of what the language suggests: low values are warm light and high values are cool light. In the camera, moreover, raising the number warms the image, because the setting compensates for a source it assumes is bluer.
The number you set does not describe the light that is there: it describes the light the camera will treat as neutral.
What value do I set for each light?
Source: Candle, fireplace; Approximate Kelvin: 1,900 K; Camera setting: 2,000-2,500 K; Result: Nearly neutral whites, with some warmth preserved
Source: Incandescent bulb; Approximate Kelvin: 2,800 K; Camera setting: 3,000 K; Result: Interior without an orange cast
Source: Golden hour; Approximate Kelvin: 3,500 K; Camera setting: 5,500 K; Result: The orange is kept, which is the point
Source: Clear midday; Approximate Kelvin: 5,500 K; Camera setting: 5,500 K; Result: Neutral reference
Source: Electronic flash; Approximate Kelvin: 5,500 K; Camera setting: 5,500 K; Result: Matches daylight
Source: Overcast; Approximate Kelvin: 6,500 K; Camera setting: 6,500 K; Result: The bluish gray is removed
Source: Shade under blue sky; Approximate Kelvin: 8,000 K; Camera setting: 7,500-8,000 K; Result: Skin without a milky tone
Source: Blue hour; Approximate Kelvin: 9,000 K and above; Camera setting: 4,000 K; Result: The blue is reinforced on purpose
The setting column does not always repeat the source column, and that is where the judgment lies: you correct when you want neutrality and deliberately mismatch when the color is the subject. Setting 5,500 K at golden hour keeps the orange you went looking for; setting 3,500 K removes it and gives you back an ordinary afternoon.
Is Kelvin the only axis?
No. The second is tint, which runs from green to magenta and corrects what the Kelvin scale cannot. Fluorescents and many cheap LEDs emit an excess of green that stays there no matter how much you move the Kelvin: the correction goes through the other slider, toward magenta.
When neither axis solves the image, the scene has mixed lights (a window at 6,500 K and a lamp at 2,800 K in the same room) and no global adjustment fixes both at once. There you decide which is the main light, correct for it and accept the cast of the other, or match the artificial source with an orange gel over the flash.
What if I shoot RAW?
Then the camera setting is just a label: the raw converter can change it afterward at no cost and with no loss. In JPEG, on the other hand, the temperature is baked into the file and recovering it is a patch.
Even when shooting RAW, it is best to fix a value and not leave auto on in any series: a panorama, a timelapse or a product batch needs all the shots to share the same reference. Auto varies from frame to frame as soon as what is inside the frame changes. See white balance for the specific setting.
Common mistakes
Leaving auto white balance on in a series. It is the number one cause of a panorama coming out with color banding.
Neutralizing golden hour. Correcting all the way to perfect white erases the reason you got up early; plan it with the golden hour calculator.
Forgetting the tint axis. With fluorescents, moving only the Kelvin leaves skin greenish.
Adjusting color in a room with warm light. Your eye adapts to the surroundings and your monitor lies about what someone else will see.
Taking it for an added effect. The blue of blue hour is real light above 9,000 K, not a filter applied in editing.
For the creative use of the setting, see the guide to creative white balance, the one on basic color theory and the article white balance outdoors: a practical guide.